Petroleum Test Equipments

Product Details:

The Viscosity Site consists of the control unit Visco Temp 30150 with a cooling unit and a cylindrical rotational viscometer Haake Viscotester 550.The complete viscosity measurement site is portable and weighs 26 kg including its robust trolley case. It can also be simply and safely send to field labs.The Visco Temp covers a temperature range from -30 °C to +150 °C (-22 °F to 302 °F) without requirement of an external cryostat. Viscosity Measuring Site is now extendable with a cooling-water recooler for temperatures down to -45 °C (-49 °F) - a cost-effective alternative to cryostats with the same capacity.

Features:

• It provides very fast cooling & heating thermoelectrical modules.
• Measures different viscosity ranges, vane sensor for examination on pipeline conditions.
• It can measure down to - 45°C.
• Portable in case of -30 to 150°C.

Applications:

• Asolute viscosity measurement
• From very low to very high viscosities.
• For newtonion & non- newtonion samples.
• Quality Control

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: VM30150

Product Details:

Thermal conductivity meter, Lamba Measuring system- this model is used for thermal conductivity measurements of liquids according to ASTM ASTM D7896-14. The unit is capable of measuring on Nano/micro particle fluids and powders.

By combining the high precision thermal conductivity sensor with a high dynamic wide range heating/cooling device, a new standard on the field of thermal conductivity measurements could be set.The measurement principle is based on a resistance measurement at a hot wire.

Features:

• Suitable for Fluids, powders, gels and Nano-fluids.
• measurement range 10 – 2000 mW/(m*K)
• wide temperature range −50 °C to 300 °C
• Usable on samples with low and high viscosity
• Small sample volume from 35 ml
• Fully automated.

 

Applications:

• Optimization of fluids development.
• Optimaization of fluids applications.
• Quality Control.
• Fluid analysis at site.
• Measurement of thermal conductivity, thermal diffusivity & specific heat capacity.

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: LM

Product Details:

High-Pressure High-Temperature Viscometer (HPHT viscometer) is the latest product of PSL. With this rotational viscometer, the viscosity of shear rate-dependent (newtonian) fluids as well as the viscosity of shear rate independent (non-newtonian) fluids can be measured under pressures of up to 1,500 bar (21,750 psi) and temperatures up to 200 °C (392 °F).The Haake Viscotester VT550 measures the viscosity of fluids and pastes fast, easy and reliable. The results - viscosity, shear stress, shear rate, yield point and operating temperature - are digitally displayed.
Additional measuring sensors, e.g. vane sensors for yield point measurement are available. With the vane sensor you can examine critical shear force for wax deposition.More challenging tasks, e.g. the automatic measuring of flow behavior of non-newtonian substances can be directly executed with pre-defined routines. Via PC, experiment runs can be freely programmed, controlled on-line and be evaluated.

Features:

• Measures low to high viscosities ( 5- 100000 mPas)
• High temperature upto 200°C
• High pressure upto 1500 bar
• Small sample volume is required (20ml)
• comfortable cleaning- dismountable sample container

Applications:

• Yield point measurement
• Gel strength measurement
• Pipeline, umbilical line restart tests
• simulation of deepwater conditions
• Stability test of emulsions
• For newtonian & non-newtonian fluids
• Absolute & dynamic viscosity

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: HPV

Product Details:

The Turbulence rheometer (TR) by PSL Systemtechnik is a fully automated laboratory plant to research fluid currents in pipelines.The plant enables significant time-savings in test series and has a compact design. An integrated PC with operating software allows for an easy handling, supervision and evaluation of test series.The measurement principle of the TR is an hydraulic piston, which moves the sample piston. 
The effects of the Drag Reducing Agent (DRA) can be observed by direct pressure measuring or calculation of the differential pressure-loss in separate segments of the capillary. To guarantee best measurement results the TR was designed without edges or changes in diameter. Special geometries of the piston and piston head enable constant acceleration values at the injection and thereby minimize shear forces.

Features:

• Minimal shear forces, no edges, constant acceleration
• Compact laboratory plant
• Different Reylonds number can be analysed in one test run
• Different capillary diameters & lengths can be used
• Reduces the duration of testing as compared to other test methods

Applications:

• Testing the efficiency of drag reducing agents (DRA)
• Optimizing DRA
• Quality Control

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: TR

Product Details:

FT-5: The Automatic Flocculation Titrimeter records precipitation processes and determines flocculation points optically. Transparent fluids and very dark crudes can be tested with exact results in a short time.

It is available as a stand-alone device or as a complete measurement system with pump, cryostat and pressure autoclave with integrated stirrer. The adjustable light intensity makes it possible to measure even dark crudes undiluted.

Features:

• Accurate and reproducible result without dilution.
• For pressure up to 700 bar (10,000 psi).
• Highly automated with control software WinFT.
• Standalone-device or complete measuring site.

 

Applications:

• For very Dark, undiluted oils.
• Determination of Flocculation Points.
• Live Oil Testing.
• In-line solid detection of asphaltene, Wax, Scale.
• Oil stability and compatibility tests for crude and condensate.
• Quality Control.

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: FT-5

Product Details:

Examination of Scale Formation in Pipelines with the Differential Scale Loop. A fully automated laboratory device is a tube blocking system to examine the precipitation and deposition of scale and other salt crystals in pipework systems like oil or water pipelines.


Features:

• Small sample volumes

• Automated tests with decreasing inhibitor concentrations

• Automated scale detection and cleaning procedure

• Exchangeable model pipeline

• Overnight runs possible

• Up to 400 bar (5800 psi)

Applications:

• Development of inhibitors

• Testing of oil or water treatment additives (Inhibitors / Dissolvers)

• Quality control

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: DSL
• Pay Mode Terms: L/C (Letter of Credit)

Product Details:

Rocking Cell System RC5-Automated hydrate test system for inhibitor screening and compatibility testing.The Rocking Cell uses one of the most stringent condition of the currentlyaccepted methods for research on hydrate inhibitors and influence of corrosion inhibitors. The measuring principleof the rocking cell is based on the steady tilting of cooled, pressurised test cells (rocking cells).

While tilting, a ball inside the camber is steadily rolling over the length of the test chamber, thereby blending the fluid-gas mixture.
The movement of the ball creates strong shear forces and turbulences in the test chamber. Thus, the conditions in pipelines are reproduced. 

For testing the test chambers are filled with a sample fluid (water or other) and a certain amount of inhibitor. The test chambers are cooled down to a given test temperature. Subsequently, the central gas supply is used, to fill each chamber to the individually required pressure of up to 200 bar (2,900 psi).The 5 test chambers are mounted on a movable axis in a closed cooling bath with cooling liquid. Only this axis is tilted during the test. This offers the advantage, that only the test chambers are moved but not the cooling bath itself. 

The Rocking Cell is extendable up to 10 test chambers.
The test chambers are magnetically attached and can thus be easily removed for filling or cleaning.

The compact Rocking Cell requires only a small amount of space and is equipped with an integrated PC.

Features:

• Turbulent mixing stringent conditions
• Long lasting experiments upto 30 days
• Variable test settings
• 5 movable test chambers extended up to 10
• Separately adjustable pressure upto 200bar
• Esy filling & cleaning

Applications:

• Examination of kinetic gas hydrate inhibitors(KHI)
• Influence of corrosion inhibitors(CI)
• Optimization of inhibitor concentration
• Quality control

  

Note:Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: RC5
• Pay Mode Terms: L/C (Letter of Credit)

Product Details:

The Sapphire Rocking Cell is a laboratory instrument to research and test low-dosage hydrate inhibitors (LDHI), corrosion inhibitors (KI), anti-agglomerates (AA) and kinetic hydrate inhibitors (KHI) and also multi-phases. The full view polished test cells are made of sapphire glass.The sapphire test cells are completely transparent.

The sapphire Rocking cell is available in three designs.

The Rocking Cell RCS2 with upto 2 test cells.

The Rocking Cell RCS6 with up to 6 test cells are models for small spacing, e.g to be placed in a fume hood.

 

The Rocking cell RCS 20 is a stand alone rig installation with up to 20 test cells.

Examination of Gas Hydrate Formation with the Gas Hydrate Autoclaves. The Gas Hydrate Autoclaves GHA 200 and GHA 350 by PSL System technique are hydrate test cells for research of the effectivity and efficiency of kinetic and thermodynamic gas hydrate inhibitors, as well as anti-agglomerates.

 

Features:

• Visual supervision of an experiment with up to 3 cameras

• Photo- and video recordings are possible

• Simulates pipeline conditions

• Long-time experiments

• Automated test schedule

• Small footprint

• Simple opening-mechanism

 

Applications:

• Research of kinetic and thermodynamic hydrate-inhibitors

• Analysis of anti-agglomerates

• Optimization of inhibitor-concentrations
• Test of low dosage hydrate inhibitors(LDHI) & corrosion inhibitors

• Quality control

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: RCS

Product Details:

H2S Analyzer 320 (DyMS) was developed for determination of H2S content in bitumen, asphalt, crude and heavy oils and refinerey products. The H2S Analyzer 320 (DyMS) measures dissolved and evolving hydrogen sulfide, mercaptans, SO2 and inherent sulphur components in bitumen and asphalt, a wide range of crude oils and refinery products under temperatures of up to +200 °C. The instrument provides very accurate and reliable results within the whole measuring range. The H2S Analyzer works for a wide range of emission levels from 1 to 10.000 ppm hydrogen sulfide for the liquid phase and up to 1000 ppm in the vapor phase. H2S Analyzer reduce scavanger treatment costs & save development and measuring time compared to the actually used test methods.The measuring principle of H2S Analyzer 320 based on DyMS method. The instrument has one - optional two - storage and one measuring containers, where the sample will be mixed permanently and hold on temperature up to +200 °C. The sample will be pumped into the measurement container - loaded with a high boiling point solvent - and mixed continuously. Afterwards the H2S is stripped off by purging nitrogen through the liquid. The mass transfer is  improved and more H2S can be detected compared to other methods. 
The use of inert gas nitrogen avoids oxidation of true H2S. The H2S concentration is finally detected by a specific sensor. In general a measurement requires max. 15 minutes. The results will be recorded, calculated and printed. 

Features:

• Measures dissolved & evolving H₂S.
• Measures H₂S, light mercaptan, SO₂ simultaneously in vapour & liquid phase.
• Two storage container
• Temperature range 30 to 200°C
• Portable test unit

Applications:

• For bitumen,asphalt,heavy fuel oils,crude & other refinery products
• Evaluation & optimization of H₂S scavengers
• Quality Control

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: H2Sanalyser320

Product Details:

Stability Analyzer for Heavy Fuel is used for stability control of heavy fuel oils, compatibility of blends and effect of additives. It measures the stability reserve of heavy fuel oils upon ageing simulation (precipitation of asphaltenes in alkane). It only takes one click and 15 minutes to measure the stability of heavy fuel oils. The method is accurate, repeatable and objective, it gives stability as a quantitative number. The instrument is easy to use, portable and robust.

 

Features:

• Confirms to ASTM-D-7061-04
• One click One number
• 15 minutes measurement
• Measures the stability reserve of heavy fuel oils
• Up to aging simulation (Precipitation of asphaltene on alkaline)

Additional Information:

• Item Code: Turbiscan-HFO

Product Details:

Gas Hydrate Autoclaves GHA 350 by PSL Systemtechnik provides convenient & better test methods to research on effectivity and efficiency of kinetic and thermodynamic gas hydrate inhibitors, as well as anti-agglomerates. It offers diverse features in a small space. Pipeline conditions are realistically simulated in the Gas Hydrate Autoclave.The effectiveness of hydrate-inhibitors can be reliably checked aPressure-resistant sapphire-glass windows in the Gas Hydrate Autoclaves allows the use of one or multiple boroscope-camera which enables observing the processes inside the autoclave. Thereby gas hydrate formation can be recorded as photo or video during an experiment. Up to six autoclaves can be operated simultaneously via one PC. 
The Gas Hydrate Autoclave GHA 350 is equipped with one borescope camera, it is mounted in the autoclaves' head and observes the sample surface from top view and optimized in a pressure range of up to 350 bar /5075 psi. The Gas Hydrate Autoclaves can easily be opened and closed by a specially designed mechanism. An integrated double jacket, temperature and pressure sensor, as well as the integrated stirrer enable a full control of experiments. Even small leakage losses are prevented by double seal sets. Thus, long-run experiments of 30 days or longer are possible. The insulation of the Gas Hydrate Autoclave supports a quick heating and cooling as well as good temperature stability at test conditions.

Features:

• Simulates pipeline Conditions
• Long term experiments
• Automated test schedule
• Photo & video recordings are possible
• Simple opening mechanism

Applications:

• Research of thermodynamic & kinetic hydrate inhibitors
• Analysis of anti-agglomerates
• Optimization of inhibitor concentrations
• Quality control

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: GHA350

Product Details:

PPT 25150/45150: The pour point tester 25150/45150 by PSL Systemtechnik is a compact lab-instrument to measure the pour point (no flow point) of oils and oils products.It measures according to the rotational method ASTM D5985.

It is characterized by high accuracy and reproduceability of measurements. By use of thermoelectric module, it does not require any external cryostat.The Pour Point Tester have been designed to meet the broad variety of customer's demands.They are accurate and reliable as well as portable and light weight.

Features:

• Fully automated and microprocessor controlled.
• High resolution and accuracy.
• No external cooling device required.
• Very compact dimensions.
• Portable and standalone or can be used with PC control.
• Portable for -45 to 150 degree C.

Applications:

• Measuring pour point in fluids.
• Analysis and optimization of pour point depressants (additives)
• Quality contriol.

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: PPT25150

Product Details:

The Cold Finger is used to examine the wax content of crude oil and condensate. The PSL Coldfinger CF 15 is equipped with up to 15 measuring places for multi-place testing. It facilitates simultaneous testing of different chemicals on a single sample or testing of different inhibitor concentrations with the same sample.The Cold Finger is simulating the temperature difference, a cooled part (finger) is inserted into the stirred and heated oil. The contained waxy components start to precipitate on the surface of the cold finger cell. By weighing the deposition after a time at a set temperature, the deposition rate can be calculated. The final amount of deposition gives the total wax content.The wax deposition rate depends not only on the finger temperatures, but on sample temperature and stirring speed, too.


Features:

• 15 measuring places for simultaneous test
• Shorter measuring times
• Samples can be separately removed during test
• Improved handling
• Highly precise measurings with weight calibrated cold finger cells
• Software for documentation

Applications:

• Determine wax content & paraffin deposition
• Measure wax appearance temperature (WAT)
• Development of inhibitors
• Optimization of inhibitor concentrations
• Quality control

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: CF15

Product Details:

Wax Flow Loop by PSL Systemtechnik is a compact laboratory instrument to research deposition effects of waxes, paraffins and asphaltenes in pipelines.
The Wax Flow Loop simulates pipeline conditions by a test capillary, which the sample is pumped through.Only 50 ml of sample amount is sufficient to know about the efficiency and effectiveness of wax inhibitors.The Wax Flow Loop also provides the possibility to assay the efficiency and effectivenes of dissolvers. This feature allows to execute Pipeline Restart Tests and Yield Stress Tests.The Wax Flow Loop is an instrument to examine wax deposition to the inner wall of the capillary via differential pressure and wax crystallisaion in the medium itself via differential temperature.The differential pressure and -temperature are continously measured and displayed as real-time diagrams on the monitor . This allows precise conclusions about development of wax depositions and crystallisation in the medium during a test run.Experiments can be run with open or closed loop mode. In open loop mode the sample is lead to a waste container. The closed loop mode is suited to run long-time experiments. In this mode, the sample is pumped back to the sample container.

Features:

• Fully automated
• Exchangeable model pipeline
• Small sample volume is requied (50ml)
• Shock-cooling effect to maximise deopsition effect & shorten test time
• Real time diagrams

Applications:

• Research on deposition of wax, paraffin & asphaltene
• Analysis of wax crystallisation
• Testing of wax dispersants
• Testing of pipeline coatings
• Development & optimization of inhibiting agents & dissolvers
• Quality control

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: WL

Product Details:

DySL - Stress-Test of Oilfield Chemicals : The Dynamic Stability Loop (DySL) is designed for testing oilfield chemicals on long term stability under most rigorous conditions in laboratory. The DySL combines multi-loop testing of viscosity and filter blocking tests for low and high temperature under pressurized conditions.

In respect to extensive testing demands, the DySL is specially designed for multiple loop test runs.It comprises up to 6 test loops for parallel testing of different alternatives oilfield chemicals or different product types.Each loop is operated seperately Cleaning and refill is possible while other loops are still runnings.

Features:

• Up to 6 pressurized test loops.
• Hot and cold bath for stress test.
• Computer controlled, automated data acquisition.
• Easy handling
• Open and closed loop testing
• Small sample volumes.

 

Applications:

• Observation of scale in pipelines and water pipes.
• Development of inhibitors.
• Optimization of inhibitor concentartion.
• Optimization of water treatments.
• Quality control.

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: DySL

Product Details:

Gas Hydrate Autoclaves GHA 200 by PSL Systemtechnik provides convenient & better test methods to research on effectivity and efficiency of kinetic and thermodynamic gas hydrate inhibitors, as well as anti-agglomerates. It offers diverse features in a small space. Pipeline conditions are realistically simulated in the Gas Hydrate Autoclave.The effectiveness of hydrate-inhibitors can be reliably checked aPressure-resistant sapphire-glass windows in the Gas Hydrate Autoclaves allows the use of one or multiple boroscope-camera which enables observing the processes inside the autoclave. Thereby gas hydrate formation can be recorded as photo or video during an experiment. Up to six autoclaves can be operated simultaneously via one PC.
The Gas Hydrate Autoclave GHA 200 is equipped with one borescope camera, it is mounted in the autoclaves' head and observes the sample surface from top view and optimized in a pressure range of up to 200 bar /2,900 psi. The Gas Hydrate Autoclaves can easily be opened and closed by a specially designed mechanism. An integrated double jacket, temperature and pressure sensor, as well as the integrated stirrer enable a full control of experiments. Even small leakage losses are prevented by double seal sets. Thus, long-run experiments of 30 days or longer are possible. The insulation of the Gas Hydrate Autoclave supports a quick heating and cooling as well as good temperature stability at test conditions.

Features:

• Simulates pipeline Conditions
• Long term experiments
• Automated test schedule
• Photo & video recordings are possible
• Simple opening mechanism

Applications:

• Research of thermodynamic & kinetic hydrate inhibitors
• Analysis of anti-agglomerates
• Optimization of inhibitor concentrations
• Quality control

Note: Price may vary depending on configuration & accessories.

Additional Information:

• Item Code: GHA200

Product Details:

We are mainly provide the wide range of Equilibrium Shapphire Cell Apparatus for CO2 Rich Mixtures. VLE measurements at low temperatures can be studied using a stirred equilibrium cell, consisting of a stirred sapphire tubular cell mounted between two Hastelloy C276 or Titanium flanges.This experimental set-up was designed for working temperatures between 200 to 470 K and pressures up to 20 MPa. In this device, known quantities of substances (liquids, liquefied gases, or gases) can be injected into the cell using Top Industrie very accurate metering pumps (PMHP) and gas tanks. For an accurate pressure measurement, three sensors are connected to the cell and heated at constant temperature. The temperature is measured directly in the cell using Pt100.

Additional Information:

• Delivery Time: 12-16 weeks